Permissible network configurations	TT, TN
Mains input voltage	3x 110 VAC to 230 VAC ±10% or 1x 110 VAC to 230 VAC ±10%
Frequency	50 / 60 Hz ±4%
Installed load	Max. 2.1 kVA
Inrush current	5 A (at 230 VAC)
Switch-on interval	>10 s
Integrated line filter per EN 61800-3, category C3	Yes
Power dissipation at device nominal power without braking resistor	110 W

DC bus connection

DC bus capacitance	2040 µF

24 VDC power supply

Input voltage	24 VDC +25% / -20%
Input capacitance	5600 µF
Current consumption	Max. 1.47 A + Current for motor holding brake

Motor connection

Quantity	1
Continuous current	3.6 Aeff
Reduction of continuous current depending on ambient temperature
Mains input voltage: 110 VAC
Switching frequency 5 kHz	No reduction
Switching frequency 10 kHz	No reduction
Switching frequency 20 kHz	No reduction
Mains input voltage: 230 VAC
Switching frequency 5 kHz	No reduction
Switching frequency 10 kHz	No reduction
Switching frequency 20 kHz	No reduction
Reduction of continuous current depending on installation elevation
Starting at 500 m above sea level	0.36 Aeff per 1000 m
Peak current	12 Aeff
Nominal switching frequency	10 kHz
Possible switching frequencies	5 / 10 / 20 kHz
Insulation stress of the connected motor per IEC TS 60034-25:2004	Limit value curve A
Max. motor line length	15 m
Protective measures
Overload protection	Yes
Short-circuit and ground fault protection	Yes
Max. output frequency	598 Hz
Terminal connection cross section
Flexible and fine-stranded wires
With wire end sleeves	0.25 to 4 mm²
Approbation data
UL/C-UL-US	30 to 10 AWG
CSA	28 to 10 AWG

Motor holding brake connection

Response threshold for open-circuit monitoring	Approx. 245 mA
Max. output current	1.3 A
Max. number of switching cycles	Unlimited since implemented electronically

Braking resistor

Peak power output	1.9 kW
Continuous power	130 W

Limit switch and reference inputs

Quantity	3
Circuit	Sink
Electrical isolation
Input - ACOPOS	Yes
Input - Input	No
Input voltage
Nominal	24 VDC
Maximum	30 VDC
Switching threshold
Low	<5 V
High	>15 V
Input current at nominal voltage	Approx. 4 mA
Switching delay	Max. 2.0 ms
Modulation compared to ground potential	Max. ±38 V

Enable inputs

Quantity	1
Circuit	Sink
Electrical isolation
Input - ACOPOS	Yes
Input voltage
Nominal	24 VDC
Maximum	30 VDC
Input current at nominal voltage	Approx. 30 mA
Switching threshold
Low	<5 V
High	>15 V
Switching delay
Enable 0 → 1, ready for PWM	Max. 100 µs
Enable 1 → 0, PWM off	Max. 2.0 ms
Modulation compared to ground potential	Max. ±38 V
OSSD signal connections	Not permitted

Trigger inputs

Quantity	2
Circuit	Sink
Electrical isolation
Input - ACOPOS	Yes
Input - Input	No
Input voltage
Nominal	24 VDC
Maximum	30 VDC
Switching threshold
Low	<5 V
High	>15 V
Input current at nominal voltage	Approx. 10 mA
Switching delay
Rising edge	52 µs ±0.5 µs (digitally filtered)
Falling edge	53 µs ±0.5 µs (digitally filtered)
Modulation compared to ground potential	Max. ±38 V

Electrical properties

Energy efficiency (IE classification)
Power loss relative to continuous apparent power	IE2 (10,25) 5.3% IE2 (50,25) 5.9% IE2 (10,50) 5.4% IE2 (50,50) 6.7% IE2 (90,50) 9% IE2 (10,100) 6.3% IE2 (50,100) 9.7% IE2 (90,100) 16.5%
Nominal losses in standby mode	12.5 W

Operating conditions

Permissible mounting orientations
Hanging vertically	Yes
Horizontal, face up	Yes
Standing horizontally	No
Installation elevation above sea level
Nominal	0 to 500 m
Maximum	2000 m
Pollution degree per EN 61800-5-1	2 (non-conductive pollution)
Overvoltage category per EN 61800-5-1	II
Degree of protection per EN 60529	IP20

Ambient conditions

Temperature
Operation
Nominal	5 to 40°C
Maximum	55°C
Storage	-25 to 55°C
Transport	-25 to 70°C
Relative humidity
Operation	5 to 85%
Storage	5 to 95%
Transport	Max. 95% at 40°C

Mechanical properties

Dimensions
Width	58.5 mm
Height	257 mm
Depth	220 mm
Weight	2.5 kg

MATERIAL NUMBER:

8V1016.50-2

DESCRIPTION:

Designed for operation on a single-phase or three-phase power mains
Modular mechanical design using plug-in modules
Integrated line filter
Integrated braking resistor
Integrated electronic restart inhibit

ACOPOS servo drive, 3x 110-230 V / 1x 110-230 V, 3.6 A, 0.7 kW, integrated line filter, braking resistor and electronic safe restart interlock

B&R 8V1016.50-2 Servo Motor Protector Drive Module 8V1016.502

PLC Interface Module

B&R PLC Module

Allen Bradley PLC Module

Beckhoff PLC Modules

Georg Fischer Piping System

Bently Nevada Extension Cable

Honeywell Automation Module

SICK Laser Sensor

Harting Connector Han

Phoenix Contact Housing

Hokuyo Laser Sensor

Yokogawa Module

Keyence Vision Systems

Euchner Safety Switch

IFM Pressure Sensor

Foxboro DCS System

B&R 8V1016.50-2 Servo Motor Protector Drive Module 8V1016.502

General information

Mains connection

DC bus connection

24 VDC power supply

Motor connection

Motor holding brake connection

Braking resistor

Limit switch and reference inputs

Enable inputs

Trigger inputs

Electrical properties

Operating conditions

Ambient conditions

Mechanical properties

MATERIAL NUMBER:

DESCRIPTION:

motorscan update ed100

nec servo driver

bldc 48v